inkyhands 20 Marly 2010

I've been a fountain pen user for several years, since I received my first Montblanc Noblesse during the 1970's. I've accrued a number of pens through the years Montblancs, Parkers, some Watermans, yet others.

However, generate income experienced using fountain pens was by using technical pens for writing.

I still enjoy using technical pens and also have a couple of individuals too. Including a lot of the Rapidographs which have fountain pen physiques, but fine technical points using the small wire inside them.

However, when they write well, they were not really created for that. To encourage them to write, you have to contain the pen almost exactly vertical. Works fine if you work with the pen to ink a line inside a drawing, although not so hot for writing.

Even though I'm about them, how about stylographs? Additionally they were built with a thin, hollow point for writing. Did they have a similar problem these technical pens have?

CS388 21 Marly 2010

I still enjoy using technical pens and also have a couple of individuals too.

If a number of your pens aren't too valuable for you, you can test out them – without too great a loss of revenue, whether it goes completely wrong.

You could attempt writing at the selected position on some wet wet-or-dry paper. Say, 800? (Maybe coarser, should you prefer a more radical re-shaping.)
When you get to your preferred shape, write on finer grades as much as 1200 or 2000 to shine and hone.

Tip: using a small amount of soap around the final grit lessens the scratching, while keeping the abrasive excellence of the grade.(Apparently. I've no citable proof.) Just make certain you fully rinse all of the soap off before re-inking.

This really is all only a guess until someone pops up having a better answer. But if you have a lot of them, fool around.

ZeissIkon 21 Marly 2010

Greater than a century ago, stylographic pens were common (at some point, apparently more prevalent than fountain pens, possibly since the valve and wire system stored blobbing low in days when modern feeds were unknown). The greatest web site stylograph along with a technical pen would be that the tube wall within the stylograph is thicker, and it is rounded over right into a roughly hemispherical point using the opening in the center. As lengthy a the wire protrudes enough to get hold of the paper, this type of pen will write at any position (used, the wires were usually lengthy enough to permit writing lower to around 30є in the paper, less than most fountain pen feeds will grant).

The tube walls in modern technical pens are extremely thin with this, and grinding the purpose off in an position would then pressure you to definitely write as of this selected position (and when you enhance the pen a hair around the upstroke, the resulting catch could throw tiny droplets of ink everywhere). What could are more effective is always to put some type of bead around the tip from the tube. One method to do this can be to disassemble the purpose (remove it the pen and take away the wire and weight) and set a small amount of thick cyanoacrylate around the tip from the tube, then make use of a suitably sized wire drill to obvious the bore therefore the wire operates properly again. A far more permanent method is always to sleeve within the tube having a bigger diameter tube that may then be polished towards the same hemispherical point which was present in stylographics before 1900 (and encountering the 1950s using the Inkograph brand).

Or you might just watch eBay to have an Inkograph and also have it restored (or perform the work yourself, they are really quite simple, although the tube mounting cone is of rather soft plastic and can easily crush or take marks from tools when attemping to unscrew it in the section).

CS388 21 Marly 2010

The tube walls in modern technical pens are extremely thin with this, and grinding the purpose off in an position would then pressure you to definitely write as of this selected position (and when you enhance the pen a hair around the upstroke, the resulting catch could throw tiny droplets of ink everywhere).

Ah. Correct. I hereby abandon my prediction and go +1 with ZeissIkon.

I'll personally compensate you for just about any pens destroyed within the interim time before ZeissIkon's answer was published.

Chthulhu 21 Marly 2010

Peter Robins 06 August 2010

However, when they write well, they were not really created for that. To encourage them to write, you have to contain the pen almost exactly vertical. Works fine if you work with the pen to ink a line inside a drawing, although not so hot for writing.

I'm able to talk no more than Rotring Isograph, but most likely it pertains to other technical pens. If you are using something similar to .20, .25, or .30, for instance, they are able to write at just about any position.

Can there be in whatever way that you could customize the point on these pens to enhance how they work when you're writing? I believed when you can round from the point, that will help. Anybody have knowledge about this?

It isn't the end whatsoever. It is the wire. You are able to verify that simply. Disassemble the end (be very carefull. ) and drop a tiny bit of ink within the tip. Since, with no wire it'll leak, should you drop more ink. Then attempt to write by using it. You will see that all of the tickly feeling is finished.

Even though I'm about them, how about stylographs? Additionally they were built with a thin, hollow point for writing. Did they have a similar problem these technical pens have?

Their tips are usually bigger. Many of them can't write that thin and small. And it is again the wire. Their is thicker and most likely well rounded.

Source: www.fountainpennetwork.com